Contributed by:
Learning Outcomes:
1. Identify a unit circle and describe its relationship to real numbers.
2. Evaluate trigonometric functions using the unit circle.
3. Use domain and period to evaluate sine and cosine functions and use a calculator to evaluate trigonometric functions.
1.
Trigonometric Functions:
4.2 The Unit Circle
Copyright © Cengage Learning. All rights reserved.
2.
What You Should Learn
• Identify a unit circle and describe its relationship
to real numbers.
• Evaluate trigonometric functions using the unit
circle.
• Use domain and period to evaluate sine and
cosine functions and use a calculator to
evaluate trigonometric functions.
2
4.
The Unit Circle
The two historical perspectives of trigonometry incorporate
different methods of introducing the trigonometric functions.
Our first introduction to these functions is based on the unit
Consider the unit circle given by
x2 + y2 = 1 Unit circle
It is called the unit circle because it has
a radius of one unit.
Figure 4.18
4
5.
The Unit Circle
As you graph any angle on the unit circle, there is a point
where its terminal side intersects the circle. The point is
(x, y)
If you graph an angle of 0 degrees or 0 radians, the
terminal side intersection corresponds to the point (1, 0).
Moreover, because the unit circle has a
circumference of 2, the angle 2 also corresponds to the
point (1, 0).
5
6.
The Trigonometric Functions
6
7.
The Trigonometric Functions
You can use these coordinates to define the six
trigonometric functions.
sine cosine tangent
cosecant secant cotangent
These six functions are normally abbreviated sin, cos, tan,
csc, sec, and cot, respectively.
7
8.
The Trigonometric Functions
8
9.
The Trigonometric Functions
In the definitions of the trigonometric functions, note that
the tangent and secant are not defined when x = 0.
For instance, because t = /2 corresponds to (x, y) = (0, 1),
it follows that tan( /2) and sec( /2) are undefined.
Similarly, the cotangent and cosecant are not defined when
y = 0.
For instance, because t = 0 corresponds to (x, y) = (1, 0),
cot 0 and csc 0 are undefined.
9
10.
Example 1 – Evaluating Trigonometric Functions
Evaluate the six trigonometric functions at each real
a. b. c.
For each t-value, begin by finding the corresponding point
(x, y) on the unit circle. Then use the definitions of
trigonometric functions.
10
11.
Example1(a) – Solution cont’d
t = /6 corresponds to the point
11
12.
Example1(b) – Solution cont’d
t = 5 /4 corresponds to the point
12
13.
Example1(c) – Solution cont’d
t = corresponds to the point (x, y) = (–1, 0).
13
14.
Domain and Period of Sine and Cosine
14
15.
Domain and Period of Sine and Cosine
Please read this slide and the next three, but do not copy
them down.
The domain of the sine and cosine functions is the set of all
real numbers.
To determine the range of these two functions, consider the
unit circle shown to the right.
15
16.
Domain and Period of Sine and Cosine
Adding 2 to each value of in the interval [0, 2] completes
a second revolution around the unit circle, as shown in
Figure 4.23.
Figure 4.23
16
17.
Domain and Period of Sine and Cosine
The values of sin(t + 2) and cos(t + 2) correspond to
those of sin t and cos t.
Similar results can be obtained for repeated revolutions
(positive or negative) around the unit circle. This leads to
the general result
sin(t + 2 n) = sint and cos(t + 2 n) = cost
for any integer n and real number t. Functions that behave
in such a repetitive (or cyclic) manner are called periodic.
17
18.
Domain and Period of Sine and Cosine
It follows from the definition of periodic function that the
sine and cosine functions are periodic and have a period of
2. The other four trigonometric functions are also periodic.
18
19.
Domain and Period of Sine and Cosine
A function f is even when
f (–t) = f (t)
and is odd when
f (–t) = –f (t)
Of the six trigonometric functions, two are even and four
are odd.
19
20.
Example 2 – Using the Period to Evaluate Sine and Cosine
Because y you have
20
+1-315-636-4485
+91 98151-74050 
